Now that Valentine’s Day is over, Easter inspiration will be popping up everywhere you look. I’ve decided to join in on the fun and offer a DIY tutorial on how to make your very own Easter chick necklace! The original little marshmallow treat these are inspired by are quite popular here in the United States – typically most people either love them or hate them. If you’re in the “love” group, you’re sure to enjoy the following tutorial! These instructions are for a necklace, but you can create the chick for any use (bracelet, earrings, or just to put on your desk!)
DIY Easter Chick Tutorial
– Yellow Polymer Clay
-Brown Polymer Clay
– Flat end head pin
– Finished necklace chain
– Pliers (round nose and flat nose recommended)
– Waxed paper (for keeping your work surface clean)
– Aluminum foil (for baking the clay in the oven)
Step 1: Gather your materials (listed above.) As you can see, I like the Sculpey brand clay. I think it’s softer to work with than some of the other brands, but any brand of polymer clay will work!
Step 2: Break off a small piece of yellow polymer clay, and begin to knead and soften the clay. This is called “conditioning” the clay.
Step 3: Once the clay has been conditioned, roll it into a ball.
Step 4: Hold the clay in one hand, and use your other hand to gently make an “edge” around the entire perimeter of the bottom of the ball.
Step 5: You can see the “edge” along the bottom of the ball here. Make the edge a little longer on one end of the ball. This will be the “tail” of the chick.
Step 6: Working on the longer end of the edge, pinch the clay together to form a soft point. (The “tail”.)
Step 7: Working towards the tail end, gently pinch the clay upward from the round dome/top section (this will be the head.)
Step 8: Working with the head area you just formed, gently pinch the tip of it and fold it towards the front of the chick (to form the beak.)
Step 9: Keep pinching the “beak” section until it has formed a small point. You can then gently push the beak downward a little bit, if you so desire.
Step 10: Now it’s time for the eyeballs! Using a pin (or the pointed end of the headpin) press a small dot onto each side of the head where you’ll be placing the eyes.
Step 11: Using a VERY small piece of brown clay (smaller than you think you’ll need! Smaller than showing here!) make a teeny tiny round dot of clay for each eyeball.
Step 12: This is where the eyeball placement comes in handy. Gently press the tiny piece of brown clay eyeball into each side of the head. You can use your fingers, or the tip of the headpin to put the clay in place. Gently press down on the clay with your finger to set it in place and flatten it slightly.
Close-up of the completed chick (with eyes!)
Step 13: Starting from the underside of the chick, gently push the headpin through the clay, making sure the flat part is on the bottom. I like to angle the pin so it exits out behind the chick’s head, although you can certainly angle it any way you choose.
Step 14: Bake the clay in your oven according to package instructions. (Mine went in for 15 minutes at 275F. Your temp/times will vary based on the brand of clay and size of your chick.)
Step 15: Once the clay has baked and cooled, you’ll want to form a wire wrapped loop with the end of the head pin. Here’s an easy tutorial from Artbeads if you aren’t sure how to do that part already: http://www.artbeads.com/howtomawrlo.html
Step 16: Attach the chick onto your necklace chain/ribbon/etc. (I had pre-made my chain already. You can make your own chain, or buy a pre-made chain. You could also slip the charm onto a ribbon.)
Ta-da! Here’s the finished necklace!
You can make these in any color of clay you choose, and for any type of jewelry. This photo is an example of various colors I had made for earrings.
Hope you enjoyed the tutorial! I’ve been working with polymer clay for over 15 years. It’s really very fun, and those with any level of skill can create something! You can browse some of my other clay creations in my Etsy shop, Victoria Camp Designs.